König KN-URC20B Provozní pokyny stáhnout pdf (Strana 12)

Manual TV set programming

1) Switch your TV set on.

2) Look up the brand of your TV set under “TV” in the code list. Single or multiple 4 digit codes are shown for

each brand.

3) Press and hold the TV Standby button (

) until the signal LED ( ) ﬂ ashes twice.

4) Use the number keys to enter the ﬁ rst four-digit code from the code list for the brand that you have selected.

The signal LED (

) ﬂ ashes twice to indicate that the code has been accepted.

5) Test the functionality of your remote control using the TV standby button (

) and the AV button (

6) If the TV set does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next

code from the code list.

7) If the TV set responds properly to all functions, your KN-URC20B is correctly programmed and can be used.

Please note the code that was used for future reference.

Manual programming for the satellite receiver and the DVB-T (Freeview)/cable-box

(STB)

1) Switch your satellite receiver or DVB-T (Freeview)/cable-box (STB) and TV set on.

2) Look up the brand of your unit under “STB” in the code list. Single or multiple 4 digit codes are shown for each

brand.

3) Press and hold the STB Standby button (

stb

) until the signal LED ( ) ﬂ ashes twice.

4) Use the number keys to enter the ﬁ rst 4-digit code from the code list for the brand that you have selected. The

signal LED (

) ﬂ ashes twice to indicate that the code has been accepted.

5) Now test the individual buttons on your remote control for function, starting with the STB Standby button

(

stb

), volume buttons (

vol

), and then with the buttons 1 to 43 (in accordance with functional

description table). The AV button (

) and TV Standby button (

) are not tested.

6) If the unit does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next

code from the code list.

7) If the unit responds properly to all functions, your KN-URC20B is correctly programmed and can be used.

Please note the code that was used for future reference.

My programming codes to use

TV STB

Automatic programming the TV set according to brand

As an alternative, and if the correct code for your TV set cannot be found for manual programming, you can use

the automatic search function by brand for programming.

1) Switch your TV set on.

2) Look up the brand of your TV set in the brand list in the appendix to this instruction manual. There is a 3-digit

brand code for each brand.

3) Press and hold the TV Standby button (

) until the signal LED ( ) ﬂ ashes twice.

4) Use the number buttons to enter the code 1 0 0 3. The Signal LED (

) ﬂ ashes twice to conﬁ rm that the

search mode has been activated.

5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have

selected. The signal LED (

) ﬂ ashes twice to indicate that the code has been accepted.

6) Hold down the TV Standby button (

) on your KN-URC20B until the TV set switches off. This process can

take several minutes.

7) As soon as the unit has switched off, push the OK button to conﬁ rm the programming (

) until the Signal

LED (

) ﬂ ashes twice.

8) Test the functionality of your remote control using the TV standby button (

) and the AV button (

). If the

TV set responds properly to all functions, your KN-URC20B is correctly programmed and can be used.

BA König KN-URC20B, 135x215 mm CS6.indd 12BA König KN-URC20B, 135x215 mm CS6.indd 12 12.09.2012 09:32:1112.09.2012 09:32:11

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 95 96

Komentáře k této Příručce

Žádné komentáře

König KN-URC20B Provozní pokyny Strana 12

Komentáře k této Příručce

Související produkty a manuály pro Dálková ovládání König KN-URC20B