König KN-URC10B Provozní pokyny Strana 11

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 80
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 10
11
Manual TV set programming
1) Switch your TV set on.
2) Look up the brand of your TV set under “TV” in the code list. Single or multiple 4 digit codes are shown for
each brand.
3) Press and hold the TV Standby button (
) until the signal LED ( ) ashes twice.
4) Use the number keys to enter the rst four-digit code from the code list for the brand that you have selected.
The signal LED (
) ashes twice to indicate that the code has been accepted.
5) Test the functionality of your remote control using the TV standby button (
) and the AV button (
av
).
6) If the TV set does not respond, or only responds partially to the commands, repeat steps 3 to 5 using the next
code from the code list.
7) If the TV set responds properly to all functions, your KN-URC10B is correctly programmed and can be used.
Please note the code that was used for future reference.
My programming codes to use
TV
Automatic programming the TV set according to brand
As an alternative, and if the correct code for your TV set cannot be found for manual programming, you can use
the automatic search function by brand for programming.
1) Switch your TV set on.
2) Look up the brand of your TV set in the brand list in the appendix to this instruction manual. There is a 3-digit
brand code for each brand.
3) Press and hold the TV Standby button (
) until the signal LED ( ) ashes twice.
4) Use the number buttons to enter the code 1 0 0 3. The Signal LED (
) ashes twice to con rm that the
search mode has been activated.
5) Use the number keys to enter the three-digit brand code from the brand list for the brand that you have
selected. The signal LED (
) ashes twice to indicate that the code has been accepted.
6) Hold down the TV Standby button (
) on your KN-URC10B until the TV set switches off. This process can
take several minutes.
7) As soon as the unit has switched off, push the OK button to con rm the programming (
ok
) until the Signal
LED (
) ashes twice.
8) Test the functionality of your remote control using the TV standby button (
) and the AV button (
av
). If the TV
set responds properly to all functions, your KN-URC10B is correctly programmed and can be used.
Note
:
It could happen, that during the search process, the KN-URC10B nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 3 to 9) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Automatic TV search
As an alternative, or if neither manual programming nor automatic programming by brand has found the correct
code for your TV set, you can use the automatic search function.
1) Switch your TV set on.
2) Press and hold the TV Standby button (
) until the signal LED ( ) ashes twice. If the button is not pushed
long enough, the TV set switches off. In this case, start the programming again by switching the TV set on.
3) Use the number buttons to enter the code 1 0 0 1. The Signal LED (
) ashes twice to con rm that the
search process has been activated.
4) Hold down the Standby button (
) on your KN-URC10B until the TV set switches off. This process can take
several minutes.
5) As soon as the unit has switched off, push the OK button to con rm the programming (
ok
) until the Signal
LED (
) ashes twice.
BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 11BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 11 12.09.2012 08:36:0012.09.2012 08:36:00
Zobrazit stránku 10
1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 79 80

Komentáře k této Příručce

Žádné komentáře